The Foundation of Plumbing Knowledge When Installing a Bathtub
The Foundation of Plumbing Knowledge When Installing a Bathtub
Blog Article
We have uncovered this article pertaining to How to Install a Bathtub listed below on the web and reckoned it made perfect sense to share it with you here.
Setting up a tub isn't specifically rocket science, but it does need strong plumbing, carpentry, and also often, tiling skills. Changing an old tub with a brand-new one is likewise a moderately hard project. If the old bathtub is easily obtainable, the job can relocate rapidly; if you have to open up a wall surface to eliminate the old tub as well as position the brand-new bathtub, the task is a lot harder. In either case, the task is within a residence handyman's skills, although you will require an assistant to move out the old bathtub and set in the brand-new one. Make sure you have actually certified yourself for the work and also fit trying it. As opposed to hiring a professional to take control of a halfway-completed job, it is better to take into consideration using one prior to you start. Opportunities are you might need an expert plumber to make tube links.
This post will certainly help you install a brand-new bath tub in your restroom if you have already bought a new bathtub and also don't require to change the plan of your previous water pipes.
Your devices as well as product list must consist of the following:
Removing Old Taps
If you require to change old faucets with new ones as a part of your setup, then the first thing you ought to do is disconnect the water system. After doing so, activate the faucets to drain pipes any water continuing to be in the system. The procedure of removing the existing taps can be fairly problematic as a result of the restricted accessibility that is commonly the instance.
Use a basin wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the taps. Have a fabric ready for the remaining water that will certainly come from the pipes. When the supply pipelines have actually been eliminated, use the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the single faucets from transforming throughout this procedure. As soon as the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned of any old sealing substance.
Prior to moving on to fit the brand-new faucets, compare the pipeline connections on the old taps to the new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the brand-new faucets to fit.
Suitable New Taps
If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic port to prevent damages to the thread. One end of the adapter fits on the plastic tail of the faucet and also the other end supplies a connection to the current supply pipes.
If you require to fit a monobloc, then you will certainly require decreasing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, position the faucet in the placing hole in the bath/basin ensuring that the washing machines are in area between the faucet and the sink. Secure the tap in place with the maker given backnut. As soon as the faucet is firmly in position, the supply pipes can be connected to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with normal faucet connectors. The former kind must be linked to the faucet finishes initially, tightening just by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have been linked.
Setting up the Bathtub
Making use of the two wooden boards under its feet, position the tub in the needed setting. The wood boards are helpful in equally spreading out the weight of the bath tub over the area of the boards instead of concentrating all the weight onto four tiny factors.
The next objective is to make sure that the tub is leveled all round. This can be attained by inspecting the level and also changing the feet on the bath tub up until the level checks out level.
To install taps, fit the bottom of the furthest versatile tap connector to the appropriate supply pipeline by making a compression join; after that do the exact same for the various other faucet.
Activate the water system and also inspect all joints as well as brand-new pipework for leakages as well as tighten them if needed. Load the bathtub as well as likewise examine the overflow outlet as well as the typical electrical outlet for leakages.
Ultimately, repair the bathroom paneling as described in the producer's instruction manual. Tiling as well as sealing around the tub must wait up until the bath tub has been made use of a minimum of once as this will settle it into its last setting.
Getting ready for the Installment
First of all, the sustaining framework supplied with the bath needs to be fitted (if required) according to the maker's directions. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is very important to make certain that if the faucet comes with a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bath, it is additionally practical to fit a supporting plate under the taps device to stop strain on the tub.
Fit the flexible tap connectors to the bottom of the two faucets making use of 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet through the hole in the bathroom. Make use of the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Make sure you make use of all of the supplied washing machines.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bath need to currently prepare to be suited its last placement.
Tiling Around the Tub
In the location where the bath meets the tile, it is essential to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can move enough to break a stiff seal, causing the water to penetrate the wall between the bath and also the tiling, causing problems with wetness as well as possible leakages to the ceiling listed below.
You can choose from a selection of coloured sealers to blend in your components and fittings. They are marketed in tubes and cartridges, as well as can sealing gaps as much as a width of 3mm (1/8 inch). If you have a bigger gap to fill, you can load it with twists of drenched paper or soft rope. Bear in mind to always fill the bathtub with water prior to securing, to permit the movement experienced when the bathtub is in usage. The sealant can break fairly very early if you do not take into account this movement prior to sealing.
Alternatively, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise easily available on the market. It is advisable to fit the tiles using waterproof or waterproof sticky as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We had been shown that editorial on How to Install a Bathtub from a good friend on our other site. Enjoyed reading our blog posting? Please share it. Help someone else locate it. Thanks a bunch for your time. Don't forget to come visit our website back soon.
Make An Appointment Report this page